Crane Axle Dana 80 Front Steering Axle Magnum C's and Knuckles Kit Overview Image

Dana 80 Front Steering Axle Magnum C's and Knuckles Kit

Crane Dana 80 Front Steering Axle Magnum Roller Kit with Wilwood Brakes Overview Image

Dana 80 Front Steering Axle Magnum Roller Kit with Wilwood Brakes

Dana 80 Front Steering Axle Magnum Roller Kit

Crane's Axle Builder Kits for Dana 80 allow you to create the Dana 80 axle you want all in one place.

The Dana 80 Magnum Roller Kit Includes:

Dana 80 Re-Tubed Housing (Pass or Driver), Magnum Inner C's, Magnum Outer Knuckles, Interlocking High Steer Arms, and Spindles/Wheel Hubs.

Optional Components: Dan 80 Seal Housings and Dana 80 Diff Cover

Typical Lead Time: 30-40 Days

Freight Note: Typically around $150 less to a COMMERCIAL address than a RESIDENTIAL address

Click to learn more about this kit

Crane Axle is proudly made in the USA

As low as $5,687.64 was $5,986.99
Availability: In stock
SKU
Dana 80 Magnum Roller Kit

Dana 80 Magnum Roller Kit

Typical Lead Time: 30-40 Days

Freight Note: Typically around $150 less to a COMMERCIAL address than a RESIDENTIAL address

Crane Dana 80 Magnum Roller Kit

This Crane Axle Assembly includes a Dana 80 Re-Tubed Housing (Pass or Driver), Magnum Inner C's, Magnum Outer Knuckles, Interlocking High Steer Arms, and Spindles/Wheel Hubs. A great start to a bad ass Dana 80 Front Axle.

Crane Axle starts your axle build with a bulletproof Dana 80 center section. We then re-tube the housing with 4" x 1/2" (.500") DOM tubes.

We MIG weld Crane Axle Magnum Inner C's to the end of the tubing for a strong hold. With this kit, we then add on Crane Axle Magnum Outer Knuckles with the included Kingpin components. These components are top of the line for Off Road use. Interlocking High Steer Arms are then installed onto the outer knuckles. The interlocking keys on these arms take the load off of any studs and put it on the knuckles themselves. Say goodbye to broken studs. Spindles/Wheel Hubs are then installed before shipping.

Read below for information on specific components.





Included Components

Magnum Inner C's

Crane Axle's Kingpin 60 Inner C is a Heavy Duty alternative to the stock Inner C. Crane's Inner C's are built out of 8620 Chromoly steel for ultimate strength and light weight right here in the USA

  • Built from 8620 Chromoly steel
  • Ultimate strength and reliability
  • Made in USA




Magnum Outer Knuckles

Crane Axle Kingpin 60 Knuckles

Crane Axle's Kingpin 60 Outer Knuckles are built from Chromoly Steel and designed for durability in hardcore Off Road wheelin.

  • Built from Chromoly Steel
  • Ultimate strength and reliability
  • Interlocking keys to High Steer Arms
  • Made in USA




Interlocking High Steer Arms

Crane's Dana 60 Interlocking Hi Steer Arms are made to be used with Crane Dana 60 Outer Knuckles.

  • Built from 1018 CR Steel
  • Superior Strength and Precision Fit
  • Keyed Interlocking system means no more broken studs
  • Measures 10" from Kingpin center to end of arm
  • Overall length of 12 1/8"
  • Made in USA




All Kingpin Components

Included Components are:

  • Crane King Pin Spring Eliminator Kit
  • Upper King Pin Cones w/ Seals
  • Upper King Pin Bushings
  • Lower Bearings/Races and Seals
  • Lower King Pin Caps (trunnions) and Hardware
  • 1/2-20 Spindle Studs




Optional Components

Dana 80 Seal Housings

Crane Axle's Dana 80 seal housings are used when building a steering axle. We build the housings to accept (2) inner seals for 2" shafts and O.D. O-rings to seal against I.D. of the axle tube. Fits 4" x .500 wall tubing.

Dana 80 Diff Cover

Crane Axle is proudly made in the USA

More Information
Axle Compatibility Dana 80
Crane Axle Builder Kit Kingpin 60 Cs and Outer Knuckles
Write Your Own Review
You're reviewing:Dana 80 Front Steering Axle Magnum Roller Kit
Your Rating