1350 Forged U-Bolt Pinion Yoke for Dana 60 - 29 Spline
3-4-5731
The 1350 Forged U-Bolt Pinion Yoke for Dana 60 is a heavy-duty replacement yoke for Dana 60 axles using a 29-spline pinion and 1350 series U-joint. Its forged construction is built to handle the torque and driveline shock found in rock crawlers, rock bouncers, trail rigs, race vehicles, and other high-load drivetrain applications.
The U-bolt retention design is a major advantage for an off-road axle because it securely captures the U-joint while remaining straightforward to service. Instead of the small retaining bolts used with traditional strap-style yokes, the U-bolts can be removed and replaced without dealing with broken or seized strap bolts—giving builders a strong, serviceable driveline connection that is easier to repair on the trail.
Includes:
- (1) 1350 Forged U-Bolt Pinion Yoke
- (2) U-Bolts
- U-Bolt Nuts & Lock Washers
Specifications
| Specification | Details |
|---|---|
| Product Type | Pinion Yoke |
| Axle Platform | Dana 60 |
| U-Joint Series | 1350 |
| U-Joint Retention | U-Bolt |
| Pinion Spline Count | 29 |
| Spline Pressure Angle | 45° |
| Ground Hub Diameter | 1.875" |
| Length Through Bore | 1.500" |
| Centerline of Joint to End of Spline | 3.030" |
| U-Joint Retaining Width | 3.625" |
| U-Joint Bearing Diameter | 1.188" |
| Maximum Joint Angle | 22° |
| Construction | Forged |
Fitment
Designed For:
- Dana 60 axle applications
- 29-spline pinion shafts
- 1350 series driveshaft U-joints
- Off-road and heavy-duty driveline builds
- Custom Dana 60 axle assemblies
Fitment Notes:
- Requires a compatible Dana 60 29-spline pinion shaft.
- Designed for a 1350 series U-joint with a 3.625" retaining width and 1.188" bearing cap diameter.
- Uses U-bolt retention rather than conventional U-joint straps.
- Verify axle model and pinion spline count before ordering.
- Verify driveshaft U-joint series before installation.
- Maximum joint angle is listed at 22°; actual operating angle depends on the complete driveshaft, suspension, and axle configuration.
FAQ
What Dana 60 does this pinion yoke fit?
This yoke is designed for compatible Dana 60 axle applications using a 29-spline pinion shaft. Because Dana 60 configurations vary, verify your pinion spline count before ordering.
What size U-joint does this Dana 60 yoke use?
This yoke is designed for a 1350 series U-joint with a 3.625" retaining width and 1.188" bearing cap diameter.
Why use a U-bolt yoke instead of a strap-style yoke?
A U-bolt yoke captures the U-joint bearing caps with two U-bolts rather than small straps and retaining bolts. For off-road builds, this provides a simple, serviceable design and eliminates the small strap bolts that can become damaged, seized, or broken during hard use.
Why use a forged pinion yoke?
The pinion yoke transfers driveline torque from the driveshaft into the differential and sees repeated shock loading. Forged construction makes this yoke well suited to large tires, low gearing, high-torque drivetrains, and demanding off-road use.
Will this yoke work with my existing driveshaft?
It will work when the driveshaft uses a compatible 1350 series U-joint and the Dana 60 uses the correct 29-spline pinion. If your driveshaft uses a different U-joint series, the driveshaft or U-joint configuration may need to be changed.
